This research was performed to determine which of the three techniques used by knee surgeons at the Mayo Clinic was the most accurate at the surgical removal (resection) of the knee-cap (patella) in a symmetric fashion during total knee replacement (arthroplasty). Although all three techniques are known to be effective, the three techniques had never been compared to one another to determine if one was more effective than the others at resecting the patella.
Resection of the patella to prepare it for placement of a patellar prosthesis is a procedure that is performed routinely in the vast majority of total knee arthroplasties (TKA) in the United States and at the Mayo Clinic. This procedure is performed by a number of different techniques that have been proved to be safe and effective. Despite this, patellar instability, tilt, obliquity, and maltracking are all possible complications of improperly resected patellae during TKA. The goals of resection are to create a patella that is symmetrical, absent of obliquity (slanting), and thick enough to receive a patellar prosthesis. Although outcomes are generally good for most described methods, to date, little had been published regarding direct comparison of these methods. Patients undergoing TKA with planned patellar resection were randomized to have their patella resected by one of three methods during primary TKA: 1) use of a cutting guide, 2) haptic feedback, or 3) free-hand resection guided by four quadrant measurements. There were three experienced fellowship-trained arthroplasty surgeons (hip and knee) performing the procedures who were all familiar and experienced with each of the three techniques being investigated. Each surgeon, within a group of 30 of their patients, performed a total 10 resections using each of the three methods listed above (30 resections per surgeon for a total of 90 resections). Before and after resection measurements of knee-cap thickness were taken and used to determine patellar symmetry. The resulting symmetry of each of the three techniques was then be compared between and within each of the three techniques and surgeons. Each procedure was also be timed from first measurement by the staff surgeon to the final measurement by that surgeon.
Study Type
INTERVENTIONAL
Allocation
RANDOMIZED
Purpose
TREATMENT
Masking
NONE
Enrollment
90
The guide is clamped onto the patella and tightened so that it remains stable. The guide has a slot that allows insertion of a standard sagittal saw blade, and this slot guides the blade as it is advanced across the patella. The thickness is then measured in the center of the patella to ensure that the resection goal is achieved. Additional resection may be performed as needed.
It consists of a free hand cut (no guide used) with a standard sagittal saw that is oriented based on osteo-cartilaginous landmarks and haptic palpation of the patella by the surgeon. The resection thickness/obliquity can be altered based on haptic feedback (use of the sense of touch) of the patella. The thickness is then measured in the center of the patella to ensure that the resection goal is achieved. Additional resection may be performed as needed.
Mayo Clinic in Rochester
Rochester, Minnesota, United States
Mean Asymmetry of the Patella After Patella Resection
Post-resection symmetry of the patella was independently assessed by a resident or fellow who was not involved in the resection. This was evaluated by dividing the patella into four equal quadrants and measuring the thickness in the center of each quadrant using a ring tipped or "C"-shaped caliper. The difference between the thickest and thinnest measurements of the patella was reported as the value of asymmetry.
Time frame: approximate average surgery time of 3 hours
The Difference Between Surgeon Goal and Actual Resection Height
This outcome measure attempts to capture the most accurate method for obtaining a desired thickness. Each patellar resection procedure began by exposing the articular surface of the patella. Once the patella was fully exposed and the surgeon measured the native patellar thickness, the timer was started. The surgeon then stated their goal for post resection thickness, and these values were recorded. After the final resection, the timer was stopped. The ability to obtain the resection goal was independently assessed by a resident or fellow not involved in the resection. This was calculated by taking the difference between the surgeon's goal and the average thickness of the four quadrants measured by the resident or fellow.
Time frame: Time 0 (prior to patella resection), and after surgery (approximately 3 hours)
Time to Complete Patella Resurfacing
Each patellar resection procedure began by exposing the articular surface of the patella. Once the patella was fully exposed and the surgeon measured the native patellar thickness, the timer was started. After the final resection, the timer was stopped.
Time frame: Time 0 (prior to patella resection), and after surgery (approximately 3 hours)
This platform is for informational purposes only and does not constitute medical advice. Always consult a qualified healthcare professional.
Resection is performed in a free handed fashion, but after resection, the thickness of the patella is measured separately in all four quadrants (superolateral, superomedial, inferomedial, and inferolateral). Additional resection is performed as needed based on the quadrant measurements and the measurements are repeated after each resection until satisfactory resection thickness and symmetry are obtained.