The purpose of this study is to compare among different designs of the occlusal surface of artificial crowns, trying to determine a guidance of fabricating artificial crowns with better mimesis of the original tooth crown in terms of morphology.
For occlusal surface design, each subject would be given 3 crowns using different fabricating guidance -- the FGP technique(FGP),the average setting technique(AVR) and conventional technique(CON), separately. Upon baseline visit, general tooth preparation procedures would be performed, including impression taking before and after treatment and tooth preparation. Sometimes photo taking is needed. On try-in visit, subjects would be ask to fill in questionaires(Likert's scale) and the adjusting time for each crown would be recorded. Moreover, t-scan would be used to assess the occlusal equilibrium. All in all, including adjusting visit for FGP, the subjects have to visit the clinic for 3 times which would take them 3-week time. The Institutional Board(IRB) of the Stomatological Hospital of Fourth Military Medical University(FMMU) would be in supervision of the whole study and is responsible for the quality assurance plan, data check and source data verification. Subject recruitment would done within those patients visit the department of prosthodontics of the Stomatological Hospital of FMMU and have an interest towards this study. One clinician would be appointed to enroll the subjects according to the standards. To avoid errors, all the examinations done in the study shall be accomplished by the same clinician and the crowns fabricated in the study shall be designed by the same technician. The clinician and the technician participated would receive adequate training before the study to ensure their performance. Every subject in the study should assign informed consents at the beginning of the study and establish case report forms(CRFs). During the study, if adverse events(such as crown chipping, crown dropping or iatrogenic gingivitis, etc) happen, subjects are required to contact the investigator within 24 hours; and the investigator should then report to the IRB within 24 hours. Following treatment or compensation would be done according to the clauses stated in the informed consent signed by the subjects. The whole study needs subjects in total. During the study, subjects have their own right to quit the study at any time if they have discussed with the investigator in advance. These subjects then are deemed as "unavailable". If subjects don't contact the investigator and quit the study(the investigators can't contact them within the follow-up period), their records then are deemed as "missing". All the information collected in the study would be protected and only be used within this study. The statistical analysis of this study would be processed with the aid of the department of statistics of FMMU.
Study Type
INTERVENTIONAL
Allocation
RANDOMIZED
Purpose
TREATMENT
Masking
SINGLE
Enrollment
12
To execute FGP technique, the occlusal surface of the interim should be back cut to leave at least 1mm occlusal space. Then apply the recording resin. Ask the subjects to close the mouth to maximum intercuspal position then perform right lateral, left lateral and protrusive movements in succession ending in maximum intercuspation position. Excessive resin then should be trimmed off and Bausch articulating paper would be used to mark the intercuspal contacts. Zinc oxide is then applied to check eccentric occlusion, trimmed off resin if there're interferences. Then the interim would be used as a copy to design the occlusal surface of the crown. (CAD/CAM)
the crowns in this group would be designed by setting virtual articulator to average mode (CAD/CAM)
Stomatological Hospital of Fourth Military Medical University
Xi’an, Shanxi, China
△OT Value
Occlusion time (OT) is defined as the time from the first contact of occluding teeth to maximum intercuspation. OT is directly related with patients' occlusal contact pattern; and some have considered it as a capable description of occlusion. In the study, the OT value of each crown would be assessed before try-in (baseline) and immediately after try-in using T-scan (FGP, AVR, CON). Try-in procedure would be finished by the same clinician. △OT was calculated for minimizing individual difference among participants. The equation for △OT was:△OT(FGP/ AVR/ CON)= OT (FGP/ AVR/ CON)-OT(baseline)
Time frame: 2 weeks(plus or minus 7 days) after tooth preparation
△DT Value
Disocclusion time (DT) is defined as the time from maximum intercuspation to complete disocclusion during lateral movement. DT related tooth contacts with muscle activity. Abnormities in DT would result in change of muscle activity, thus facilitate the occurrence of temporomandibular joint disorders. In the study, the DT value of each crown would be assessed before try-in (baseline) and immediately after try-in using T-scan (FGP, AVR, CON). Try-in procedure would be finished by the same clinician. △DT was calculated for minimizing individual difference among participants. The equation for △DT was: △DT(FGP/ AVR/ CON)= DT (FGP/ AVR/ CON)-DT(baseline)
Time frame: 2 weeks(plus or minus 7 days) after tooth preparation
Occlusal Adjusting Time for Crowns
Try-in procedure would be finished by the same clinician. The occlusal adjusting time would be counted using a timer and recorded.
Time frame: 2 weeks(plus or minus 7 days) after tooth preparation
Likert's Scale
The questionaire was designed to evaluate participants' feeling towards the occlusal interference. It would be given to the subject after immediately try-in the crowns. In the questionaire: Score 0 = No interference (feel comfortable while biting on the artificial crown) Score 1 = Moderate interference(could feel the artificial crown is higher when biting on the artificial crown, but when firmly clenched, the upper teeth could bite on the lower ones) Score 2 = High interference(the artificial teeth is higher that the upper teeth couldn't bite on all the lower teeth when firmly clenched)
This platform is for informational purposes only and does not constitute medical advice. Always consult a qualified healthcare professional.
Time frame: 2 weeks(plus or minus 7 days) after tooth preparation