In this study, the point at which gingival thickness (GT) should be measured was investigated. Measurements were made from three different points. It was classified as thin and thick in two ways, according to the average of these three different points and the point corresponding to the base of the gingival groove, which is frequently used in the literature. And these two classifications were compared.
The morphology of the soft tissue around the teeth (buccolingual GT and keratinized gingival width) is defined as the "gingival phenotype". One of the most important considerations when assessing gingival phenotype is the objective quantification of GT, and various methods have been used to measure GT. However, there is no clear consensus in the literature regarding the anatomical point where GT is measured in the buccal region. For this reason, it is thought that measurements made from different points also affect the classification of gingival phenotype. The aim of this study was to investigate the cut-off values in clinical parameters according to the average GT value of different measurement points and the GT value at a single point. The study was designed as cross-sectional study. Participants were divided into two groups based on thin and thick gingival phenotypes in two different classifications. The first classification was based on the GT measurement taken from the base of the gingival sulcus, while the second classification was based on the average of GT measurements taken from three points (base of the gingival sulcus, 1 mm apical to the base of the gingival sulcus, and 2 mm apical to the base of the gingival sulcus. Other clinical and morphological parameters of the participants, who were divided into two groups (thin and thick) according to these classifications, were also measured with a digital caliper and periodontal probe. These parameters are keratinized gingival width (KGW), gingival groove depth (SD), crown width (CW), crown length (CL), crown width/crown length (CW/CL), papilla height (PH), gingival angle (GA). is. Among these parameters, the unit of measurement for GA is angle. CW/CL is the ratio. Other measurements were measured in mm. For all parameters, cut-off values were obtained through statistical measurements made according to two classifications. And these measurements were compared. In addition, the compatibility of the GT measurements of the three points with each other was also examined. Participants Ondokuz Mayis University's Clinical Research Ethics Board approved the consent form and study protocol (210/2021). Participants with 1195 teeth sites, were enrolled in the study from September 2022 to August 2023. Participants were recruited from University Ondokuz Mayis included patients, dental/ hygiene students. A single calibrated examiner (SY) performed all clinical and morphological measurements.
Study Type
INTERVENTIONAL
Allocation
RANDOMIZED
Purpose
SCREENING
Masking
NONE
Enrollment
50
GT was measured from the point corresponding to the base of the gingival sulcus and 1 mm and 2 mm apical to this point. If the GT was ≤1 mm, it was considered a thin phenotype, and if it was \>1 mm, it was considered a thick phenotype.
Ondokuz Mayis University Faculty of Dentistry Department of Periodontology
Samsun, Turkey (Türkiye)
Examining the sensitivities and sensitivities of two different gingival phenotype classifications based on three-point average GT measurement and single-point measurement using Receiver Operating Characteristic Analysis (ROC).
Two different classifications compared for determining the gingival phenotype of 50 participants were evaluated for sensitivity and specificity using Receiver Operating Characteristic analysis (ROC). Gingival thicknesses for gingival phenotypes were measured in 1195 teeth. The data were recorded in the SPSS program, and ROC analysis was conducted. The Area Under the Curve (AUC) value is a general measure of classification performance in ROC analysis. AUC value ranges between 0 and 1, with a higher value indicating better performance. The result criterion in ROC analysis is used to evaluate the accuracy and discriminative power of classifications.
Time frame: 1 month
Examining the agreement of GT measurements at three different points in 50 patients, 1195 teeth, using Kappa analysis.
50 patients, 1195 teeth in the gingival region were measured in millimeters (mm) using a digital caliper with a precision of 0.001 mm. Kappa analysis was conducted on the collected data. Kappa analysis is used to assess the agreement between two or more measurements or between observers. In this study, the agreement between three points and the average GT value was evaluated using Kappa analysis. Kappa value ranges between -1 and 1: a Kappa value approaching 1 indicates excellent agreement between anatomical points. A negative Kappa value indicates worse agreement than random chance between anatomical points.
Time frame: 1 month
This platform is for informational purposes only and does not constitute medical advice. Always consult a qualified healthcare professional.