Respiratory Rehabilitation Based on Eccentric Exercice on Treadmill After Thoracic Surgery

Rectus femoral thickness

The dominant quadriceps (defined by the leg that is usually used to climb stairs or kick a ball) is measured, with the patient's starting position being supine with the knee completely extended and relaxed. While previous studies suggested a minimum of 30 minutes of rest before performing the ultrasound, more recent studies indicate that 5 minutes after adopting the supine position, measurements normalize. There is no consensus on the measurement point, but it is proposed to place the probe at the midpoint of the muscle length (50% rule), taking the greater trochanter and proximal edge of the patella as reference. It is also advisable to place the probe midway between the medial and lateral edges of the muscle. Once the placement point of the probe has been determined, it is placed as perpendicular as possible to the skin using a generous amount of transducer gel and exerting the minimum possible pressure to avoid compression of the dermal surface and muscle distortion.

Time frame: Baseline, 3 weeks, 2 months

Diaphragmatic excursion

A convex probe of 2.5 to 3.5 MHz is used. In obese subjects, to have better visibility, the frequency chosen is 1.5 MHz. The subjects are in a supine position, with the head of the stretcher flat and their legs bent at 30-45º. The probe is positioned firmly below the right costal arch and on the line drawn corresponding to the middle of the clavicle, orienting it cranially. At that point, the dome of the right hemidiaphragm is visualized, appearing as a thick hyperechoic line. The highest diaphragmatic position is sought, which is the part of the diaphragm that produces the most craniocaudal excursion, and the transducer is kept firmly in position during the phases of the respiratory cycle and measurements of tidal volume breathing. The M mode modality is then activated, which provides us with the diaphragmatic movement pattern, placing the M beam line around 30º in the posterior part of the cranio-caudal midline: cranio-caudal diaphragmatic excursions.

Time frame: Baseline, 3 weeks, 2 months

Diaphragm thickness

The measurement of the thickness of the diaphragm is taken in the right hemidiaphragm since it is more accessible than the left through its hepatic window. To evaluate the thickness, a linear probe at 10-12MHz is used, placing it perpendicular to the intercostal space between the 9th and 10th rib, in the anterior part of the axillary line. At this level, 3 parallel layers with different echogenicity are observed corresponding to the pleura, the diaphragm and the peritoneum. The measurement is carried out with M mode, where the image is frozen in an unforced expiration (representing the functional residual capacity) and in a maximum inspiration. The distance between the inner edge of the pleural line and the inner edge of the peritoneal line is measured. The measurement is carried out three times and the average of the three is taken.

Time frame: Baseline, 3 weeks, 2 months

6MWT

In this test, the patient is asked to walk the maximum possible distance along a minimally traveled 30-meter corridor for a period of 6 minutes following a standardized protocol. The primary outcome will be the distance walked in 6 minutes measured in meters, with several reference equations that allow normality values to be calculated. It is essential to follow a standardized 6MWT methodology to obtain reproducible and reliable results, which is why the indications of the SEPAR Manual of Procedures are followed.

Time frame: Baseline, 3 weeks, 2 months

Perceived effort

It is measured through the Borg scale, which consists of a vertical scale from 0-10 that relates the perceived effort when making physical effort with a numerical value that ranges from 0 (minimal effort) to 10 (extreme effort).

Time frame: Baseline, 3 weeks, 2 months

Measurement of maximum respiratory pressures (MIP and PEM).

The pressure gauge we use is the RP Check. To measure PEM, the patient must insert the mouthpiece into his or her mouth, with the bite blocks between the teeth; You should inhale as much air as possible until you completely fill your lungs (to full lung capacity) and then exhale as hard as possible and for as long as possible (1.5 seconds minimum). To measure PIM, the patient must insert the mouthpiece into his mouth, exhale as much air as possible to empty his lungs until reaching the residual volume, and then inhale with as much effort as possible and for as long as possible (minimum 1.5 seconds). We perform three consecutive measurements of each one, allowing the patient to rest one minute between each one, and we note the best result.

Time frame: Baseline, 3 weeks, 2 months

Functional capacity

Through the 30-second sit to stand test. We previously measured basal oxygen saturation and heart rate; The patient performs the test with his arms crossed over his chest; We time 30 seconds and write down the result. Next, we measure the saturation of oxygen and heart rate.

Time frame: Baseline, 3 weeks, 2 months

Grip strength measurement in both hands

With the Hand Grip Dynamometer Kern Map Version 1.2 dynamometer, taking into account the dominant hand and possible injuries to the upper limbs that may interfere with the test result.

Time frame: Baseline, 3 weeks, 2 months

Spirometric assessment of FEV1

We performed three consecutive measurements with the Vitalograph copd-6™. You need to enter your age, height and gender. The patient must inhale completely, hold the breath, gently bite the mouthpiece and then blow as hard as they can for 6 seconds, allowing them to rest for a minute between each one and we will record the best result.

Time frame: Baseline, 3 weeks, 2 months

Life quality

SF-12 Health Questionnaire

Time frame: Baseline, 3 weeks, 2 months